Jotun Jotamastic 90 Aluminium Reviews

Jotun Jotamastic 90 Aluminium is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistant, high solids, high build product. This version of Jotun Jotamastic 90 is aluminium pigmented for improved barrier effect. Specially designed for areas where optimum surface preparation is not possible or required. Jotun Jotamastic 90 Aluminium provides long lasting protection in environments with high corrosivity and can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel, galvanised steel, stainless steel, aluminium, concrete and a range of aged coating surfaces. Primarily designed for maintenance and repair for general use. It can also be used in marine environments for outside hulls, exterior and interior areas. Jotun Jotamastic 90 Aluminium is recommended as a protective coating for offshore environments, including splash zones, refineries, power plants, bridges, buildings, mining equipment and general structural steel. Quick Links - Click To Jump To Section: Features & Benefits Approvals & Certificates Product Data Film Thickness Surface Preparation Application Drying & Curing Time Heat Resistance Product Compatibility Storage & Shelf Life Caution Health & Safety Features & Benefits Aluminium pigmented version of Jotun Jotamastic 90 for improved barrier effect Two component polyamine cured epoxy mastic coating Surface tolerant, abrasion resistant, high solids, high build product Specially designed for areas where optimum surface preparation is not possible or required Provides long lasting protection in environments with high corrosivity Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments Touch dry in 4 hours at 23 °C Approved for PSPC for Crude Oil Tanks according to IMO Res. MSC 288(87) NORSOK System 1, Rev.5 Suitable for properly prepared carbon steel, galvanised steel, stainless steel, aluminium, concrete and a range of aged coating surfaces Primarily designed for maintenance and repair for general use It can also be used in marine environments for outside hulls, exterior and interior areas Recommended as a protective coating for offshore environments, including splash zones, refineries, power plants, bridges, buildings, mining equipment and general structural steel Approvals & Certificates Approved for PSPC for Crude Oil Tanks according to IMO Res. MSC 288(87) NORSOK System 1, Rev.5 Grain, Newcastle Occupational Health When used as part of an approved scheme, this material has the following certification: Low Flame Spread in accordance with EU Directive for Marine Equipment Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8 Additional certificates and approvals may be available on request. Product Data Technical Data Solids by volume 80 ± 2 % Gloss level (GU 60 °) Semi Gloss (35-70) Flash point 35 °C Density 1.4 kg/l VOC-EU 234 g/l The provided data is typical for factory produced products, subject to slight variation depending on colour. All data is valid for mixed paint. Small colour variations may occur when changing between the two curing agents. If exposed to weathering without topcoat, the Wintergrade (WG) version will yellow at a faster rate than the same colour in Standard grade. Film Thickness Recommended Film Thicknesses Theoretical Spreading Rate Dry Wet   100µm 125µm 8m²/l 300µm 375µm 2.7m²/l Surface Preparation To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.   Surface Preparation Substrate Minimum Recommended Carbon Steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless Steel The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile Aluminium The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile Galvanised Steel Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile Sweep blast-cleaning using non-metallic abrasive leaving a clean, rough and even pattern Shop Primed Steel Clean, dry and undamaged shop primer (ISO 12944-4 5.4) Sa 2 (ISO 8501-1) Coated Surfaces Clean, dry and undamaged compatible coating Clean, dry and undamaged compatible coating Concrete Low pressure water washing to a rough, clean, dry and laitance free surface. Minimum 4 weeks curing. Moisture content maximum 5 %. Prepare the surface by means of enclosed blast shot or diamond grinding and other appropriate means to abrade the surrounding concrete and to remove laitance Please refer to the Application Guide (AG) for full details. Application Application Methods: Spray: Use airless spray Brush: Use a suitable brush. Care must be taken to achieve the specified dry film thickness Roller: May be used for small areas. Not recommended for first primer coat. Care must be taken to achieve the specified dry film thickness Please refer to the Application Guide (AG) for full details. Product Mixing: Jotamastic 90 Alu Comp A - 3.5 part Jotamastic 90 Standard Comp B - 1 part Pot Life: 2 hours @ 23°C Thinner/Cleaning Solvent: Thinner: Jotun Thinner No. 17 Guiding Data for Airless Spray: Nozzle tip (inch/1000): 19-25 Pressure at nozzle (minimum): 150 bar/2100 psi Drying & Curing Time Substrate Temperature -5 °C 0 °C 5°C 10°C 23°C 40°C Surface (touch) dry - - 20 h 12 h 4 h 1.5 h Walk-on-dry - - 40 h 20 h 6 h 3 h Dry to over coat, minimum - - 30 h 10 h 3 h 1.5 h Dried/cured for service - - 28 d 14 d 7 d 2 d For maximum overcoating intervals, refer to the Application Guide (AG) for this product Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks, imprints or other physical damage Dry to over coat, minimum: The recommended shortest time before the next coat can be applied Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended environment/medium Heat Resistance   Temperature   Continuous Peak Dry, atmospheric 90 °C - Immersed, sea water 50 °C 60 °C Peak temperature duration max. 1 hour. The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures. Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in the system have similar heat resistance. Product Compatibility Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Previous Coat: Epoxy shop primer, inorganic zinc silicate shop primer, zinc epoxy, epoxy, epoxy mastic, inorganic zinc silicate Subsequent coat: Polyurethane, polysiloxane, epoxy, acrylic, vinyl epoxy Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to technical@rawlinspaints.com for more information. Storage & Shelf Life Shelf life at 23 °C Jotamastic 90 Alu Comp A - 48 Months Jotamastic 90 Standard Comp B - 24 Months In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection. Caution This product is for professional use only The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation Applicators and operators shall use appropriate personal protection equipment when using this product This guideline is given based on the current knowledge of the product Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work Health & Safety Please observe the precautionary notices displayed on the container Use under well ventilated conditions Do not inhale spray mist Avoid skin contact Spillage on the skin should immediately be removed with suitable cleanser, soap and water Eyes should be well flushed with water and medical attention sought immediately Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to technical@rawlinspaints.com for more information.